electrical engg interview questions and answers

9. Explain advantages of storage batteries

Few advantages of storage batteries are mentioned below:
• Most efficient form of storing energy portably.
• Stored energy is available immediately because there is no lag of time for delivering the stored energy.
• Reliable source for supply of energy.
• The energy can be drawn at a fairly constant rate.

10. What are the different methods for the starting of a synchronous motor.

Starting methods: Synchronous motor can be started by the following two methods:
• By means of an auxiliary motor: The rotor of a synchronous motor is rotated by auxiliary motor. Then rotor poles are excited due to which the rotor field is locked with the stator-revolving field and continuous rotation is obtained.
• By providing damper winding: Here, bar conductors are embedded in the outer periphery of the rotor poles and are short-circuited with the short-circuiting rings at both sides. The machine is started as a squirrel cage induction motor first. When it picks up speed, excitation is given to the rotor and the rotor starts rotating continuously as the rotor field is locked with stator revolving field.

11. Name the types of motors used in vacuum cleaners, phonographic appliances, vending machines, refrigerators, rolling mills, lathes, power factor improvement and cranes.

Following motors are used: -
• Vacuum cleaners- Universal motor.
• Phonographic appliances – Hysteresis motor.
• Vending machines – Shaded pole motor.
• Refrigerators – Capacitor split phase motors.
• Rolling mills – Cumulative motors.

State Thevenin’s Theorem:

According to thevenin’s theorem, the current flowing through a load resistance
Connected across any two terminals of a linear active bilateral network is the ratio open circuit voltage (i.e. the voltage across the two terminals when RL is removed) and sum of load resistance and internal resistance of the network. It is given by Voc / (Ri + RL).

13. State Norton’s Theorem

The Norton’s theorem explains the fact that there are two terminals and they are as follows:
• One is terminal active network containing voltage sources
• Another is the resistance that is viewed from the output terminals. The output terminals are equivalent to the constant source of current and it allows giving the parallel resistance.
The Norton’s theorem also explains about the constant current that is equal to the current of the short circuit placed across the terminals. The parallel resistance of the network can be viewed from the open circuit terminals when all the voltage and current sources are removed and replaced by the internal resistance.

14. State Maximum power transfer theorem

The Maximum power transfer theorem explains about the load that a resistance will extract from the network. This includes the maximum power from the network and in this case the load resistance is being is equal to the resistance of the network and it also allows the resistance to be equal to the resistance of the network. This resistance can be viewed by the output terminals and the energy sources can be removed by leaving the internal resistance behind.

Explain different losses in a transformer.

There are two types of losses occurring in transformer:
• Constant losses or Iron losses: The losses that occur in the core are known as core losses or iron losses. Two types of iron losses are:
o eddy current loss
o Hysteresis loss.
These losses depend upon the supply voltage, frequency, core material and its construction. As long as supply voltage and frequency is constant, these losses remain the same whether the transformer is loaded or not. These are also known as constant losses.
• Variable losses or copper losses: when the transformer is loaded, current flows in primary and secondary windings, there is loss of electrical energy due to the resistance of the primary winding, and secondary winding and they are called variable losses. These losses depend upon the loading conditions of the transformers. Therefore, these losses are also called as variable losses.

16. Explain different types of D.C motors? Give their applications

Different type of DC motors and their applications are as follows:-
• Shunt motors: It has a constant speed though its starting torque is not very high. Therefore, it is suitable for constant speed drive, where high starting torque is not required such as pumps, blowers, fan, lathe machines, tools, belt or chain conveyor etc.
• Service motors: It has high starting torque & its speed is inversely proportional to the loading conditions i.e. when lightly loaded, the speed is high and when heavily loaded, it is low. Therefore, motor is used in lifts, cranes, traction work, coal loader and coal cutter in coalmines etc.
• Compound motors: It also has high starting torque and variable speed. Its advantage is, it can run at NIL loads without any danger. This motor will therefore find its application in loads having high inertia load or requiring high intermittent torque such as elevators, conveyor, rolling mill, planes, presses, shears and punches, coal cutter and winding machines etc.

17. Explain the process of commutation in a dc machine. Explain what are inter-poles and why they are required in a dc machine.

Commutation: It is phenomenon when an armature coil moves under the influence of one pole- pair; it carries constant current in one direction. As the coil moves into the influence of the next pole- pair, the current in it must reverse. This reversal of current in a coil is called commutation. Several coils undergo commutation simultaneously. The reversal of current is opposed by the static coil emf and therefore must be aided in some fashion for smooth current reversal, which otherwise would result in sparking at the brushes. The aiding emf is dynamically induced into the coils undergoing commutation by means of compoles or interpoles, which are series excited by the armature current. These are located in the interpolar region of the main poles and therefore influence the armature coils only when these undergo commutation.

Comment on the working principle of operation of a single-phase transformer.

Working principle of operation of a single-phase transformer can be explained as
An AC supply passes through the primary winding, a current will start flowing in the primary winding. As a result, the flux is set. This flux is linked with primary and secondary windings. Hence, voltage is induced in both the windings. Now, when the load is connected to the secondary side, the current will start flowing in the load in the secondary winding, resulting in the flow of additional current in the secondary winding. Hence, according to Faraday’s laws of electromagnetic induction, emf will be induced in both the windings. The voltage induced in the primary winding is due to its self inductance and known as self induced emf and according to Lenze’s law it will oppose the cause i.e. supply voltage hence called as back emf. The voltage induced in secondary coil is known as mutually induced voltage. Hence, transformer works on the principle of electromagnetic induction.

19. Define the following terms:-

• Reliability,
• Maximum demand,
• Reserve-generating capacity,
• Availability (operational).

Reliability: It is the capacity of the power system to serve all power demands without failure over long periods.
Maximum Demand: It is maximum load demand required in a power station during a given period.
Reserve generating capacity: Extra generation capacity installed to meet the need of scheduled downtimes for preventive maintenance is called reserve-generating capacity.
Availability: As the percentage of the time a unit is available to produce power whether needed by the system or not.

20. Mention the disadvantages of low power factor? How can it be improved?

Disadvantages of low power factor:
• Line losses are 1.57 times unity power factor.
• Larger generators and transformers are required.
• Low lagging power factor causes a large voltage drop, hence extra regulation equipment is required to keep voltage drop within prescribed limits.
• Greater conductor size: To transmit or distribute a fixed amount of power at fixed voltage, the conductors will have to carry more current at low power factor. This requires a large conductor size.